Respondida
Generate and acquire signals with a DT9857E box using Matlab
It is all about DAQ DT9857E issue. Once we had also the same issue - a kind of exponential decay. So far, I remember what we ...

alrededor de 1 año hace | 0

| aceptada

Respondida
help with wavelet analysis - wcoherence plot
If understood your question correctly, follow this doc: https://www.mathworks.com/help/wavelet/ref/wcoherence.html#d126e131143 ...

alrededor de 1 año hace | 0

Respondida
How to move the Yaxis exponent outside
Here is one example how to get it done: % Sample data for plot display x = linspace(0, 2*pi, 100); y = 1e6 * sin(x); %% De...

alrededor de 1 año hace | 1

Respondida
how to find point from Table data in Simulink?
Do the followings: Feed the temperature and density values as inputs to the lookup table block The output of the lookup tab...

alrededor de 1 año hace | 1

Respondida
Ray tracing in antenna chamber
Have you checked out this documentation: https://www.mathworks.com/help/comm/ref/rfprop.raytracing.html?s_tid=answers_rc2-1_p4_...

alrededor de 1 año hace | 0

Respondida
Is this a logical Error in Matlab ? exp (pi*i*6) = 1.000000000000000 - 0.000000000000001i. WHY an i component ?, should just be 1
It is all about a display format: format short exp(pi*i*6) % compare with this: cos(6*pi)+1i*sin(6*pi) % Compare this: fo...

alrededor de 1 año hace | 0

Respondida
Multiple loops to build structure?
It can be done somewhat what like this one: GN = {'Group 1:'; 'Group 2:'; 'Group 3:'}; NA = {'North'; 'East'; 'West']; for ...

alrededor de 1 año hace | 0

| aceptada

Respondida
How do I graphic
The given inequality does not have explicit solution. Therefore, by ignoring analytical constraints, these can be obtained: sym...

alrededor de 1 año hace | 0

Respondida
Starting with the ramp signal r(t) and unit step signal u(t) given below, please write the codes to plot the following transformed versions (a-f):
t=-10:10; figure plot(t,t); grid on xlabel('Samples') ylabel('Amplitude') title('Ramp') figure t2=[zeros(1,100), on...

alrededor de 1 año hace | 0

Respondida
unable to connect blocks in Simulink
Use Simulink-PS converter block: https://www.mathworks.com/help/simscape/ref/simulinkpsconverter.html

alrededor de 1 año hace | 0

| aceptada

Respondida
how to plot two m.file in one plot
use plot(x, y), e.g.: x = [-5:5;2*(-5:5); 3*(-5:5)]; y = [3*x.^2+3*x-3; -5*x.^2+5*x-15; -2*x.^2-3*x-13;]; plot(x(1,:),y(1,:),...

alrededor de 1 año hace | 0

Respondida
Inverse FFT of a matrix
Just looking at your attached figure, it is clear along x axis is time. inverse FFT gives back time domain data from freq domain...

alrededor de 1 año hace | 0

Respondida
Why can't I run my code? (tfest function)
Here it is running ok: x = readtable('data_thermal_pulse.txt'); time = x.Var1; T1 = x.Var2-x.Var2(1); input = x.Var4; Ts = ...

alrededor de 1 año hace | 0

Respondida
Why does this function not work for decimals?
Here is the corrected answer (Note abs(x)<=1): % x = input("Please enter the value of x (in radians): "); % Here "input" prom...

alrededor de 1 año hace | 0

| aceptada

Respondida
How to find an area below the curve follwed by x and y axis having two different parameters?
That would be something like this: DATA = [53 100; 26.5 88.5; 9.5 64.95; 4.75 46.85; 2.36 25.34; 0.85 23.14; 0.425 0;]; ...

alrededor de 1 año hace | 0

Respondida
help understand the step size of the electrical engine dyno example
Click on Modeling Tab --> Model Explorer --> Base Workspace, and then you will see that the sampling time is 1E-5 in seconds. Se...

alrededor de 1 año hace | 0

Respondida
How to randomly sample output times in Simbiology?
To randomly generate values using MEAN and STD values, normrnd() fcn can be used: MEAN_val = 15; % Mean in minutes STD_dev ...

alrededor de 1 año hace | 0

Respondida
How to get rid of Noise in Simulink?
There are a few blocks can be used. E.g., Discrete Filter (Transfer Function), Discrete FIR Filter, etc., whcih can be found: Si...

alrededor de 1 año hace | 0

Respondida
Matlab Plotting command problem
Even though you have not mentioned any error, there is a tiny point linked with hold on command. It needs to be followed at the ...

alrededor de 1 año hace | 0

| aceptada

Respondida
How to ignore special characters and retrieve the data prior to the character
Here is one possible solution, to get the data correctly from the data file: % Open the data file for reading FID = fopen('tem...

alrededor de 1 año hace | 0

Respondida
Solve equations of motion containing matrices and partial derivatives
Your posted code has a few critical issues to be addressed before executing it. (1) epsilon_rp is undefined; (2) y(1) =4.3; bu...

alrededor de 1 año hace | 0

Respondida
Summing two signals should result in zero, but doesn't
Note that the matlab's PRECISION is not ABSOLUTE. See this example of Pythogorian theorem: a = -pi:pi/100:pi; F = 1 - (sin(a)....

alrededor de 1 año hace | 0

Respondida
how to convert a 3D surface into a 2D contour?
Note that it is clear from the colorbar scale (Figure 2 in your question) that there must be another operation before obtaining ...

alrededor de 1 año hace | 0

Respondida
Error in resampling function
If you want to use fs = 5000 Hz, then the command syntax has to be resample(x_siganl, time, fs_new) This is how it should be don...

alrededor de 1 año hace | 0

| aceptada

Respondida
How to compute forces in global reference frame?
Presuming that you are also using some blocks from SimScape toolbox in the Simulink environment, here are some points to conside...

alrededor de 1 año hace | 0

Respondida
How do I change the current directory in Simulink Onramp?
Even if you are working online, you can still go for "Save As" option (upper left corner) to select the directory where to save ...

alrededor de 1 año hace | 1

Respondida
how to convert a 3D surface into a 2D contour?
This is how it can be done: H = openfig('ds2.fig'); % This is the extracted plot figure h = findobj(gca, 'Type', 'surfac...

alrededor de 1 año hace | 0

Respondida
Use of interp2 in an arbitrary dataset
Is this what you wanted to obtain: % Given DATA: Data = [ 0.25 0.25 0.5; 0.50 0.60 1.5; 0.75 0.75 3.0];...

alrededor de 1 año hace | 0

Respondida
How to do bit-wise operations on symbolic variables that may be very long possibly larger than inter 64
Is this what you are trying to get: syms a b c n % Create symbols a = 12345; b = 9867; c = sym(0); n = 0; while a > ...

alrededor de 1 año hace | 1

Respondida
Plotting negative errorbar on semilogx
It looks like this is how to display the missing half of error bar values. The solution with the x- axis limit set up: D = read...

alrededor de 1 año hace | 0