Respondida
How to break a waveform waveform into its constituent harmonics using FFT and see the harmonic waveforms at each frequency?
Hi Rasula, I understand that you need to isolate and observe the waveform at different harmonic frequencies of a voltage signa...

2 meses hace | 0

Respondida
Enabled Subsystem does not reliably disable
Hi, I understand that the Enabled Subsystem sometimes stays on for two time points instead of one because of how Simulink hand...

2 meses hace | 0

Respondida
How to get accurate RPM using a Raspberry pi board with Simulink?
Hi Jorge, I understand you are facing an issue with timing for the RPM measurement in Simulink. To improve accuracy and handle...

2 meses hace | 0

Respondida
How to add Get function to the Simulink model generated code
Hi Oldirch, I understand that you are encountering errors when trying to generate code from your Simulink model when including...

2 meses hace | 0

| aceptada

Respondida
Processing 5 input of matrices into a fuzzy logic system
Hi Berna, I understand that need to process your five input matrices to generate a 207x216 output matrix. You can follow the...

2 meses hace | 0

Respondida
How to get closed loop frequency response when MPC as a feedforward controller?
Hi Ayesha, I understand that you need to perform Bode plot analysis for a plant model with Proportional-Integral (PI) control ...

2 meses hace | 0

Respondida
USRP N210 rx() returning data vector with different length
Hi Diogo, The error you are encountering happens when the number of samples returned by `rx()’ (i.e., `len’) is not consistent...

2 meses hace | 0

Respondida
How can I make a connection from the ePWM block to the MOSFET driver of the invertor circuit in Simulink Matlab 2024a?
I understand that you are working with the TI F280049C microcontroller to generate SPWM signals in Simulink and you need to conn...

2 meses hace | 0

Respondida
servo motor with PWM controller
Hi borboev, I understand you need to simulate a tracking drive with a PWM controller. You can follow the below steps to perfor...

2 meses hace | 0

Respondida
MATLAB Fault Analysis - "Continuous-time signals support faults only if its destinations are discrete" Error Command
Hi Krishna, I understand that you are getting an issue when you tried to trigger a fault using “Simulink Fault analyser”. “S...

2 meses hace | 0

Respondida
pv array mppt model doesn't work as expected
Hi Diana, I understand that in “PV array connected to buck-boost converter model”, the voltage is not being considered in the ...

2 meses hace | 0

Respondida
environment of a ROV in simscape
Hi Yasine, I understand that you have exported a model of a Remotely Operated Vehicle (ROV) from SolidWorks into a simulation ...

2 meses hace | 0

Respondida
Can any one help? how to develop the code or logic for electric vehicle charging and discharging limits as mentioned in picture and what should be the values of threshold.
Hi Imran, I understand that you are asking about the logic that controls the charging and discharging limits of electric vehic...

2 meses hace | 0

| aceptada

Respondida
Issue with DTC of PMSM at 40kHz PWM Frequency
Hi MD, I understand that in "Direct Torque Control of PMSM Using Quadrature Encoder or Sensorless Flux Observer" example you a...

2 meses hace | 0

Respondida
Modeling of IEEE recommended Electrical Protection of Electrical Generator in Simulink
Hi Saqib, I understand that you are looking into the relays components, to implement electrical generator protection in Simuli...

2 meses hace | 0

Respondida
Simulation error when using global data store and code generation
Hi Thomas, I understand that you are facing challenges when integrating a second referenced model that accesses global data sto...

2 meses hace | 0

Respondida
Suscripted Assignment in to Mxarray is not supported for code generation
Hi Joseph, I understand that you are facing an error when trying to convert MATLAB code to C/C++ using MATLAB Coder. This er...

2 meses hace | 0

| aceptada

Respondida
in System identification, if input is PWM signal....
Hi Minjae, To know about how to use PWM signal as an input in the System Identification Toolbox you may follow these steps: ...

3 meses hace | 0

Respondida
How to convert the input bump's height to force exerted by that bump?
Hi Faheem, To accurately simulate the effect of a road bump on your mass-damper system you can follow these steps: Modelling...

3 meses hace | 0

Respondida
How to filter out noisy data on QRS complex dataset with a program?
Hi Eugene, To develop a program that filters out noisy QRS complex data and creates visualizations, consider the following ste...

3 meses hace | 0

Respondida
How to change an offline parameter estimation to online task ?
Hi Yasser, As you want to use a recursive algorithm to continuously estimate and update the parameters in real-time, you can f...

3 meses hace | 0

Respondida
Does the NR HDL Downlink Receiver work on real raw data?
Hi Marvell, I understand that you are encountering a challenges with your 5G Downlink Receiver code, when transitioning from ...

3 meses hace | 0

Respondida
Generate host interface script and Generate Simulink software interface model unable to select.
Hi Gaurav, In addition to the steps mentioned by Pratyush, you can also try the following: Make sure to Set the path to Xilin...

3 meses hace | 0

Respondida
Seeking help on real time signal monitoring using XCP on Ethernet (TCP/IP and UDP/IP) and C2000 (F28388) Microncontroller
Hi Ismail, I understand that you need to monitor several low-frequency signals in real-time, specifically the 3-phase grid vol...

3 meses hace | 1

Respondida
Is it possible to export measurement reading of Signal Statistics in Simulink Scope block to workspace? If it is possible, then how?
Hi Syafiq, I understand that you want to export ‘RMS’ value of signal. One of the approaches is using a “MATLAB Function” bloc...

3 meses hace | 0

Respondida
How to access state-space matrices of a power-system simlink model?
Hi Adhithya, I understand that you are required to extract the state-space matrices (A, B, C, D) that describe the internal dy...

3 meses hace | 0

Respondida
Call to inv() function seems to have (undesired) impact on Thread pool or maxNumCompThreads()
Hi Jan, I understand that you are encountering unexpected CPU utilization behaviour when using thread-based parallel pools ...

3 meses hace | 0

Respondida
THD analysis of mathematical simulink model
Hi Pritham, I understand that you need to perform the THD analysis in simunlink. The ‘powergui’ block can calculate the Tot...

3 meses hace | 0

Respondida
Matlab fitnet function ignores some input variables that contain NaN values
Hi Jorge, I understand that you are experiencing an issue in training the model due to NaN values. Following steps helps in ad...

5 meses hace | 0

Respondida
delay Output parameter in Simulink - equivalent to function dde23
Hi David, I understand that you are having issues in replicating the delay behaviour observed in continuous-time models within ...

5 meses hace | 0