Respondida
Linux binaries generated by MATLAB OS Manager for SOC blockset create read only /mnt folder unable to pass your own tests of verification and unable to run example models
Hi Sai Kumar, The issue you are facing usually arises when the Linux file system on the board is mounted as read-only and the...

4 meses hace | 0

Respondida
Spectrum Analysis on signals in the Simulation Data Inspector
Hi Jack Daniels, It is possible to perform spectrum analysis (Fast Fourier Transform (FFT)) on signals using the Simulation D...

4 meses hace | 0

Respondida
Design of Dynamic Voltage Restorer.
Hi Brandon, The design procedure you followed for the “Dynamic Voltage Restorer (DVR)” seems to be quite comprehensive. You ...

4 meses hace | 0

Respondida
Simulink Data Inspector offset the time of an entire Run
Hi Stephen McLaren, To Change the time base of a given run by an addition or subtraction to all time entries and update of al...

4 meses hace | 1

| aceptada

Respondida
How can I get 3 outputs from the battery ?
Hi Ahmed ElMashad, To obtain three outputs (State of Charge (SOC), current, and voltage) from the “Battery (Generic model)” b...

4 meses hace | 0

Respondida
Simscape - Combine Harmonic Drive Driveline and Multibody
Hi Jannik, To integrate the “Harmonic Drive” block from Simscape Driveline with Simscape Multibody joints and solids, you can...

4 meses hace | 0

Respondida
Two-Phase PMLSM mathematical model
Hi Stepan Dvorak, To implement a two phase PMLSM mathematical model from Simscape blocks, you can use: Basic power electroni...

4 meses hace | 0

Respondida
How to reduce the effect of one of the manipulated variables in an MPC controller with a MISO model as the internal model?
Hi Dawn Ivan, To increase the effect of one manipulated variable on the output in the MISO model with MPC, you can follow the...

4 meses hace | 0

Respondida
How to design an MPC for a nonlinear MISO system?
Hi Nicy Scaria, To build a MISO nonlinear model controlled using MPC in which one input should serve as the manipulated varia...

4 meses hace | 0

Respondida
matlab/simulink using digital IO pins ??
Hi Aera, To use the digital IO (e.g. PMOD0_0) pins on the ZCU111 and ZCU216 boards without a pre-existing block in the librar...

4 meses hace | 0

| aceptada

Respondida
Polyspace command line execution
Hi Kalai Ragu, The error message indicates that the script is not receiving a username when trying to connect to the Polyspac...

4 meses hace | 0

Respondida
Arduino Mega2560, Support Package for Arduino Hardware Test Connection Failed
Hi Dudu Arife, The serial connection failure with Arduino Mega2560, Support Package for Arduino Hardware can be resolved by t...

4 meses hace | 0

Respondida
Nonlinear MPC is not converging. Although the predictions go towards the reference
Hi Marcos, I understand that you are facing a convergence issue due to NPMC Controller as it is not sending new inputs to the...

4 meses hace | 0

| aceptada

Respondida
Interference modeling in simulink
Hi Fumihiko Sato, In interference modelling in Simulink in which the primary signal and the interferer signal are having diff...

4 meses hace | 0

Respondida
Is it possible to control Zynq PS MIO using Embedded Coder?
Hi Martin, Simulink primarily interfaces with AXI-connected peripherals on the PL (Programmable Logic) side. You can try the...

4 meses hace | 0

Respondida
Virtual Vehicle Composer model doesn't work
Hi Ömer Ergün, The errors you are facing while building EV model using Virtual Vehicle Composer app indicates that: “fatal e...

4 meses hace | 0

Respondida
Matlab Battery builder Ambient port to simulate Heat sink with air cooling
Hi Mohammad, You can simulate air cooling without using a coolant plate on the battery module’s bottom using the “Simscape Co...

5 meses hace | 1

Respondida
Simscape Battery Capacity Estimator
Hi Gokul, In the result it indicates that the battery capacity drops from 20 Ah to 13.3 Ah over the course of 5 WLTP profiles...

5 meses hace | 0

Respondida
Error compiling Simscape network for model Loss_BuckConverter
Hi Shyam, The error message you are encountering in the Loss_BuckConverter Simulink model is due to a unit mismatch in the ther...

5 meses hace | 0

Respondida
Simulink Sensorless FOC Motor Example for LAUNCHXL-F280039C and BOOSTXL-DRV8323RS
Hi John, I understand that you are trying to implement the Sensorless FOC of BLDC motor, and when you run the host model, the...

5 meses hace | 0

Respondida
Absolute encoder Offset calibration PMSM
Hi Pratheesh, I understand that you are trying to determine the offset of an absolute encoder by injecting a small ( V_d ) an...

5 meses hace | 0

Respondida
Frequency change through load change in grid connected VSC rectifier based system. System detunes when connected to synchronous generator model.
Hi Brinda R, I understand that you are facing issues when using a Synchronous generator as a source for VSC Rectifier based s...

5 meses hace | 1

Respondida
Using Reinforcement Learning Agent with PX4 in ROS/Gazebo for Iris Drone - PID Gain Issue?
Hi Gaurav, I understand that you are facing an issue while deploying the RL agent developed using the UAV Toolbox's multiroto...

5 meses hace | 0

Respondida
Control of stand alone three phase inverter using c2000 block set in Simulink
Hi George, I understand that you are trying to implement the control system on a Texas Instruments F28379D microcontroller fo...

5 meses hace | 0

Respondida
Linear hall sensor for FOC
Hi Jamie, I understand that for PMSM motor control application using Field-Oriented Control (FOC) with linear Hall sensors, y...

5 meses hace | 0

Respondida
Transfer function where some of the coefficients are dependent on the output Y(S)
Hi Wynand, I understand that you are trying to implement the elevator system where the weight and cable stiffness changes as th...

5 meses hace | 0

| aceptada

Respondida
when i package app and simulink file,why have this error
Hi Bx, I understand that you are facing error when trying to package app and Simulink file. The error message indicates that...

6 meses hace | 0

Respondida
Cod for location of UPFC for transient stability analysis PSO algorithm
Hi Yosef Demis, I understand that you are looking for code for location of UPFC for transient stability analysis PSO algorithm...

6 meses hace | 0

Respondida
How do I export MATLAB code to Aspen Plus
Hi NURUL AINA SYAHIRAH, I understand that you want to export the code for Membrane reactor (MR) model created in MATLAB to Asp...

6 meses hace | 0

Respondida
SIMSCAPE MULTIBBODY CANTILEVER BEAM MODEL
Hi Usha, I understand that you are simulating a Cantilever beam using Simscape Multibody and are trying to get the resonant an...

6 meses hace | 0