Respondida
reduce mesh quantity in isosurface plot
Hi @Saurav and @Star Strider, I've read through the thread and appreciate both the original question and the thoughtful respo...

11 meses hace | 0

Respondida
Is it possible to use two or more GPUs with the UAV Toolbox simultaneously?
Hi @Jones, Thanks for your update. Noted that you're using UAV Toolbox for UAV simulation with HIL and integrating aerodyn...

11 meses hace | 0

Respondida
MATLAB won't invert a function in the Laplace domain...
Hi @John, I took a look at your gamma distribution Laplace inversion problem, and you've hit a classic limitation of MATLAB's...

11 meses hace | 0

Respondida
C2000 CMPSS to ePWM Trip Zone / Digital Compare connection
Hi @Valeriy, Thank you for your detailed question regarding overcurrent protection on the Delfino F28377S MCU using CMPSS and...

11 meses hace | 0

Respondida
blfread with CAN-frame and J1939-frame
Hi @Florian, Thanks for your question regarding reading J1939 frames using `blfread('myBLF.blf')`. I understand you're seeing...

11 meses hace | 0

Respondida
C Caller error when passing 2D array inside struct via Simulink bus
Hi @ 주형, I understand the compilation error you're encountering with the C Caller block when passing 2D arrays within structs...

11 meses hace | 0

| aceptada

Respondida
create array and plot the function
Dear @SP, I'm writing to follow up on your MATLAB implementation from October 29, 2018, and to address the recent technic...

11 meses hace | 0

Respondida
How to correctly implement a pid control and fuzzy logic control on synchronous generator tied to ieee bus system?
Hi @Frans, I've conducted a thorough analysis of the latest MathWorks documentation and your Simulink model for implement...

11 meses hace | 0

| aceptada

Respondida
Incorrect calculation between CRS coordinate transformation
Hi @Cristobal, I reviewed the workflow for converting coordinates from *EPSG:2084 (Hito XVIII 1963 / UTM 19S)* to *EPSG:32719...

11 meses hace | 0

| aceptada

Respondida
Neumann boundary condition in a diagonal matrix
Hi @Hugo, Thanks for sharing your code and the detailed explanation of your approach. I see you're trying to increase the a...

11 meses hace | 0

Respondida
HYBRID ENERGY STORAGE SYSTEM SUPERCAPACITOR BATTERY OFF-GRID SOLAR POWER SYSTEM
Hi @Muhammad, Thank you for sharing your simulation files and the detailed discussion thread. I've carefully reviewed all you...

11 meses hace | 0

Respondida
Coriolis Matrix of a 14 DOF bipedal robot won't compile its matlab function
Hi @Giovanni Maria, After spending several hours researching MATLAB documentation and robotics literature online, I believe I...

11 meses hace | 0

| aceptada

Respondida
Please provide me the matlab code for 8-bit integer arithmetic coding and decoding.
Hi @Harpreet, I understand you're encountering issues with reconstructing a binary vector after arithmetic encoding and decod...

11 meses hace | 0

Respondida
how to find similiarity of peak/pattern time series?
Hi @Nirwana, Thank you for sharing your code and detailing your analysis objectives. I understand that your primary goal is t...

11 meses hace | 0

Respondida
Error in building simulink code for PX4-V6x
Hi @Thai Hoa, Thank you for sharing your challenge regarding compilation of Simulink-generated code for the PX4 FMU V6X. Alth...

11 meses hace | 0

| aceptada

Respondida
Building and Embedding a Reduced Order Model in National Instruments Hardware (cRIO)
Hi @Patrick, *Original Request*: " _I could do with some guidance on a task required on a National Instruments (NI) LEM contr...

11 meses hace | 0

Respondida
Scatter point plot into plot3d or any surface
Hi @Hugo David, I saw your question about creating a surface from your scattered x,y,z data points. Yes, you can definitely m...

11 meses hace | 1

Resuelto

Basic Mathematics 2
If a 4’ x 8’ sheet of ½” plywood weighs W lbs and you cut an L” x L” robot base from this material, approximately how much weigh...

11 meses hace

Resuelto

Calculate load on arm 1
A robot is designed with a motor directly attached at the pivot point of the lifting arm. The L inch arm has a weight of W1 lbs...

11 meses hace

Resuelto

Mechanical Advantage of a Gear Train
Calculate the mechanical advantage of a gear train. The mechanical advantage of a gear couple is given by MA = T_o/T_i where ...

11 meses hace

Resuelto

Calculate the acceleration of a crate
What is the acceleration of a crate if two robots apply F1 N and F2 N of force respectively and a frictional force of FR N acts ...

11 meses hace

Resuelto

Coefficient of Kinetic friction
A robot exerts a F1 lb. force horizontally on a W lb. crate across a concrete floor at a constant speed. What is the coefficien...

11 meses hace

Resuelto

Current through resistor
Three resistors (R2, R3, R4) are connected in parallel as shown in the figure. If this combination is connected in series with ...

11 meses hace

Respondida
Export an Image as a Geotiff that is not aligned with Lat/Long Grid
Hi @Richard, Thank you for your detailed question. Based on your description, here’s how you can handle your rotated image an...

12 meses hace | 0

| aceptada

Respondida
BILSTM input data length
Hi @Walid, Yes, you can input short feature vectors to BiLSTM networks, though this requires proper data formatting. BiLSTM l...

12 meses hace | 1

Respondida
Unable to fit HDL coder design into FPGA
Hi @John, I don’t currently have access to Simulink or MATLAB toolboxes to replicate your setup directly, but I reviewed Math...

12 meses hace | 0

| aceptada

Respondida
Why my PLUTO cant capture the signals
Hi @Mert, Based on the RX code you shared and your comment about not receiving signals on a different PC with a different ADA...

12 meses hace | 0

Respondida
function argument pow error
Hi @Cesar, Let me address your comment:” _not sure why I'm getting this error, any help will be appreciated. thanks_" The ...

12 meses hace | 1

| aceptada

Respondida
Generation of proto and thunk files for distribution
Hi @Eric, To automate proto and thunk file generation in a CI/CD process, a headless MATLAB environment (or MATLAB Docker image...

12 meses hace | 0

Respondida
Issues with nlinfit - not fitting second parameter? Fitting a Blackbody curve
Hi @Caelan, Thank you for sharing your code and detailed description of the issues. I have reviewed your approach and specifi...

12 meses hace | 0

| aceptada