Matthew Mishrikey
Followers: 0 Following: 0
Estadísticas
12 Preguntas
7 Respuestas
CLASIFICACIÓN
5.942
of 289.676
REPUTACIÓN
8
CONTRIBUCIONES
12 Preguntas
7 Respuestas
ACEPTACIÓN DE RESPUESTAS
66.67%
VOTOS RECIBIDOS
2
CLASIFICACIÓN
of 19.575
REPUTACIÓN
N/A
EVALUACIÓN MEDIA
0.00
CONTRIBUCIONES
0 Archivos
DESCARGAS
0
ALL TIME DESCARGAS
0
CLASIFICACIÓN
of 144.052
CONTRIBUCIONES
0 Problemas
0 Soluciones
PUNTUACIÓN
0
NÚMERO DE INSIGNIAS
0
CONTRIBUCIONES
0 Publicaciones
CONTRIBUCIONES
0 Público Canales
EVALUACIÓN MEDIA
CONTRIBUCIONES
0 Temas destacados
MEDIA DE ME GUSTA
Feeds
Pregunta
variables with scope local to subsystem
I'm a bit confused about variable scope. I think I know what's going on but am looking for confirmation and maybe advice on th...
alrededor de 2 años hace | 1 respuesta | 0
1
respuestaRadio Button Mask for Simscape Block
I figured out a way. I saw a snippet of code in one of the videos on the topic, and it gave me enough clues to write a callback...
alrededor de 2 años hace | 0
| aceptada
Pregunta
Radio Button Mask for Simscape Block
I have a stock Simscape block (Cauer Element) that has two parameters - Resistance and Tau. I am trying to add a mask to modify...
alrededor de 2 años hace | 1 respuesta | 0
1
respuestaPregunta
get_param fails with simscape block
Weird/unexpected behavior, not sure if it's a bug. I'm trying to use get_param to access a stock simscape thermal component. I...
alrededor de 2 años hace | 1 respuesta | 0
1
respuestaBasic Slider Switch question
I think I figured out a way. I hope there's a better solution because this seems like a royal pain. 1) in the simscape compone...
alrededor de 2 años hace | 0
Basic Slider Switch question
I think I'm getting closer to an answer here. I setup slider switch to control a constant block, which feeds a data store wri...
alrededor de 2 años hace | 0
Pregunta
Simscape Block Parameter not Tunable
I wish to control a Simscape block parameter using the dashboard slider switch. I select Temperature Source, but the slider swi...
más de 2 años hace | 1 respuesta | 0
1
respuestaPregunta
Simulink dashboard switch to control masked parameter
I wanted to have a slider switch control such that On position would make it 1 Ohm and off position would make it 5 ohms. The s...
más de 2 años hace | 1 respuesta | 0
1
respuestaTwo circles geometry problems
Not clear from the second drawing what the dl of interest is. Let's assume dl is the distance between the left edge of each ci...
más de 2 años hace | 0
| aceptada
Control Design Onramp with Simulink
Enter learning.simulink.launchOnramp('controls') in your MATLAB window.
más de 2 años hace | 2
Pregunta
Parameter Writer block not recognizing blocks
In image below I show a sim with a slider switch that modifies the constant block on the left. This the uses a goto/from block ...
más de 2 años hace | 1 respuesta | 0
1
respuestaIs there a way to nest transfer functions?
Okay, nevermind, found the solution is to use s = tf('s') rather than tf([num dem]).
más de 2 años hace | 0
| aceptada
Pregunta
Is there a way to nest transfer functions?
I wish to build up a transfer function inside a for loop such that each iteration builds up a new transfer function based on pre...
más de 2 años hace | 1 respuesta | 0
1
respuestaPregunta
Basic Slider Switch question
I was curious if it was possible to make a slider switch dashboard element control more than one block simultaneously. Alterna...
más de 2 años hace | 3 respuestas | 0
3
respuestasSimscape/Simulink persistent variable in algebraic loop
I think I managed to figure out a solution. As suggested elsewhere a delay block can "break" the algebraic loop. I needed thr...
más de 2 años hace | 0
| aceptada
Pregunta
Simscape/Simulink persistent variable in algebraic loop
I have a simple Simscape electrical model containg a circuit that trips if a current is exceeded. I want the trip to happen a c...
más de 2 años hace | 2 respuestas | 0
2
respuestasPregunta
Generate Zth transient thermal impedance curves with Simscape
Simscape has some nice thermal domain elements like Cauer thermal model elements. I was looking to generate a set of Zth curves...
más de 2 años hace | 1 respuesta | 0
1
respuestaPregunta
Trying to convert Kelvin to Celsius in Simscape code
I have a simulation with some Simscape Thermal and Electrical elements. The electrical element is a modification of the stock t...
más de 2 años hace | 1 respuesta | 0
1
respuestaPregunta
simscape block node arrangement
In the IGBT example here: https://www.mathworks.com/help/physmod/sps/ug/Troubleshoot-of-spice-nigbt-conversion.html the gener...
más de 2 años hace | 1 respuesta | 0