PMSM Configuration

R2026b

Configure PMSM system parameters

Since R2022b

• 

PMSM Configuration block

To add a block to a model, double-click the canvas and start typing the block name. Then, select the block from the list.

Libraries:
Motor Control Blockset HDL Support / Electrical Systems / Motors

Description

The PMSM Configuration block generates the configuration signal for a permanent magnet synchronous machine/motor (PMSM). You can use this signal to update parameters of a PMSM block that support FPGA deployment, such as the PMSM HDL block.

Examples

Field-Oriented Control (FOC) of PMSM Using Hardware-in-the-Loop (HIL) Simulation

Uses hardware-in-the-loop (HIL) simulation to implement the field-oriented control (FOC) algorithm to control the speed of a three-phase permanent magnet synchronous motor (PMSM). The FOC algorithm requires rotor position feedback, which is obtained by a quadrature encoder sensor. For more information on FOC, see Field-Oriented Control.

• Open Example

Ports

Output

Config — Block configuration signal

vector

Configuration signal for a PMSM, which includes the following parameters that you configure using this block.

Configuration element			Units
Number of pole pairs			-
Stator resistance per phase			ohm
Stator d-axis inductance			Henries
Stator q-axis inductance			Henries
Permanent magnet flux linkage constant			Weber
Inertia			kgm^2
Back electromotive force, EMF			Vpk_LL/krpm Vpk_LL is the peak voltage line-to-line measurement
Viscous damping			N·m/(rad/s)
Mechanical input configuration (Torque or Speed)			-

Data Types: single

Parameters

Block Options

Mechanical input configuration — Select port configuration

Torque (default) | Speed

This table summarizes the input and output ports in each configuration.

Mechanical input configuration parameter value			LdTrq/Spd port configuration
Torque			LdTrq
Speed			Spd

Sample Time (Ts) — Sample time after which block executes again

1e-6 (default) | scalar

The fixed time interval (in seconds) between every two consecutive instances of block execution.

Parameters

Number of pole pairs — Pole pairs

4 (default) | scalar

Number of pole pairs, P, in the motor.

Stator resistance per phase (Ohm) — Resistance of stator

0.02 (default) | scalar

Stator resistance per phase, R_s, in ohm.

Stator d-axis inductance (H) — d-axis inductance

1.7e-3 (default) | scalar

Stator inductance, L_d, in H.

Stator q-axis inductance (H) — q-axis inductance

3.2e-3 (default) | scalar

Stator inductance, L_q, in H.

Permanent flux linkage constant (Wb) — Flux linkage constant

0.2205 (default) | scalar

Permanent flux linkage constant, λ_pm, in Wb.

Inertia (kgm^2) — Physical inertia

0.0027 (default) | scalar

Physical inertia of the motor, J, in kg.m^2.

Viscous damping (Nm/rad/s) — Viscous damping

4.924e-4 (default) | scalar

Viscous damping of the motor, F, in N·m/(rad/s).

Static friction (Nm) — Static friction

0 (default) | scalar

Static friction in the motor, T_f, in N·m.

Programmatic Use: Add Block

To add the block programmatically, use the add_block function with one of these library block paths as the source.

"mcbhdllib/Electrical Systems/Motors/PMSM Configuration"

Example: add_block("mcbhdllib/Electrical Systems/Motors/PMSM Configuration","myModel/myBlock",MakeNameUnique="on")

Version History

Introduced in R2022b