I2C Controller Write
Write data to I2C peripheral device or I2C peripheral device register
Libraries:
Embedded Coder Support Package for STMicroelectronics Discovery Boards /
STM32F769I-Discovery
Embedded Coder Support Package for STMicroelectronics Discovery Boards /
STM32F746G-Discovery
Description
The I2C Controller Write block writes data to an I2C peripheral device that is connected to the board. Using this block, you can write data to a specific register on the I2C peripheral device.
For more information on I2C communication, see Support I2C Communication.
Ports
Input
Data — Data to write to the I2C peripheral device
scalar | vector
Data Types: int8
| uint8
| int16
| uint16
| int32
| uint32
| single
| double
Output
Status — Status of the write operation
scalar
When you select the Output error status
parameter, an output port, labeled as Status
, becomes
available.
The port outputs 0
for a successful write
operation.
Data Types: uint8
Parameters
I2C module — I2C module to write data
0
(default) | integer greater than or equal to 0
Specify the I2C module on the board to write data to the I2C peripheral device.
Peripheral address — The I2C peripheral address to write data
hex2dec('48')
(default)
Specify the I2C peripheral address to write the data. The I2C peripheral device address is a 7-bit address.
Specify this address as an integer or in hexadecimal format by using
hex2dec()
, for example, ‘hex2dec(‘61’)’.
Peripheral byte order — Byte ordering that your I2C peripheral device supports
BigEndian
(default) | LittleEndian
The 2-byte ordering options are:
BigEndian - The most significant byte is sent first over the I2C bus.
LittleEndian - The least significant byte is sent first over the I2C bus.
Enable register access — Option to write to a specific I2C peripheral register
on (default) | off
When you select this parameter, the block writes data to the I2C peripheral register that you specify in the Peripheral register address parameter.
When you clear this parameter, the Send NACK at the end of data transfer and Remove stop bit at the end of data transfer parameters are displayed. Using these parameters, you can modify the write operation according to your requirements.
Peripheral register address — The I2C peripheral register address to write data
uint8(1)
(default)
Specify the I2C peripheral register address to write the data.
Specify this address in 8-bit unsigned integer or in hexadecimal format.
To specify the address in 8-bit unsigned integer, use
uint8()
, for example, ‘uint8(20)’. To specify the
address in hexadecimal format, use hex2dec()
, for
example, ‘hex2dec(‘20’)’.
For more information on register read/write, see I2C Register Read/Write.
Dependencies
This parameter appears only when you select Enable register access parameter.
Send NACK at the end of data transfer — Option to send Not Acknowledge bit at the end of data transfer
off (default) | on
When you select this parameter, the I2C Controller Write block sends a NACK (Not Acknowledge) bit to the peripheral device with the final byte.
When the peripheral device receives the NACK, it waits for a STOP condition from the I2C controller block. The controller block generates either a STOP condition to abort the transfer or a repeated START condition to start a new transfer.
When you clear this parameter, the I2C Controller Write block sends an ACK (Acknowledge) bit to the peripheral device at the end of every byte. The ACK indicates that the I2C Controller Write block is ready to read the next byte from the peripheral device.
Dependencies
This parameter appears only when you clear Enable register access parameter.
Remove stop bit at the end of data transfer — Option to remove STOP bit at the end of data transfer
off (default) | on
When you clear this parameter, the block sends a STOP condition. This condition indicates that the block has terminated the data transmission and the I2C bus is free for any other I2C controller block to initiate the read/write operation.
When you select this parameter, the block sends another START condition followed by an address and read/write bit. The block sends any number of start conditions recursively. Such a repeated START condition allows write operations to the peripheral devices without releasing the bus. No other controller block interrupts the operation.
Dependencies
This parameter appears only when you clear Enable register access parameter.
Output error status — Option to display the error status during data transmission
off (default) | on
When you select this parameter, an output port, labeled as
Status
, becomes available.
The port outputs 0
for a successful write
operation.
See Also
I2C Controller Read (Embedded Coder) | Workaround for Interrupt Workflow with Sensors
Comando de MATLAB
Ha hecho clic en un enlace que corresponde a este comando de MATLAB:
Ejecute el comando introduciéndolo en la ventana de comandos de MATLAB. Los navegadores web no admiten comandos de MATLAB.
Select a Web Site
Choose a web site to get translated content where available and see local events and offers. Based on your location, we recommend that you select: .
You can also select a web site from the following list:
How to Get Best Site Performance
Select the China site (in Chinese or English) for best site performance. Other MathWorks country sites are not optimized for visits from your location.
Americas
- América Latina (Español)
- Canada (English)
- United States (English)
Europe
- Belgium (English)
- Denmark (English)
- Deutschland (Deutsch)
- España (Español)
- Finland (English)
- France (Français)
- Ireland (English)
- Italia (Italiano)
- Luxembourg (English)
- Netherlands (English)
- Norway (English)
- Österreich (Deutsch)
- Portugal (English)
- Sweden (English)
- Switzerland
- United Kingdom (English)