Simulate Audio Visualizer on Raspberry Pi Sense HAT

Introduction

Audio visualization is a technique of displaying an image or an animation that is synchronous to audio data being played. Using this technique, the Simulink model displays colored bars on the 8-by-8 LED matrix on Sense HAT. The movement of the bars is synchronized with the audio being played.

Audio Visualizer

In this example model, the Audio File Read block reads the specified audio file and outputs it as Pulse Code Modulation (PCM) data on the Raspberry Pi hardware. The block is configured to read 8192 audio samples at each time step.

The Audio Processing subsystem computes a Fast Fourier Transform (FFT) across the samples of audio data. The subsystem converts the most significant 1024 samples from the computed FFT into logarithmic scale, reducing large dynamic variations in the frequency spectrum.

The MATLAB Function block, FFT2RGB, divides 1024 samples into 8 groups, and then calculates the length of each LED bar to be displayed on the Raspberry Pi Sense HAT.

The ALSA Audio Playback block plays the input audio through the default audio jack of the Raspberry Pi hardware. If the specified audio file is a mono file, convert it into stereo using the Vector Concatenate block. For example, in this model, the default audio file, guitartune.wav, is used. Because this file is mono, use the Vector Concatenate block to convert it to stereo.

Prerequisites

Before you start with this example, we recommend that you complete the following examples:

Required Hardware

To run this example, you must have the following hardware:

Configure and Run Audio Visualizer Simulink Model

1. Connect a pair of speakers or headphones to the analog audio output of the Raspberry Pi hardware.

2. Plug the Sense HAT module into the GPIO pins of the Raspberry Pi hardware.

3. Open the raspberrypi_audioVisualizer Simulink model.

4. On the Simulink model toolbar, select Apps > Run on Hardware Board > Options....

5. Browse to Hardware Implementation > Hardware board settings > Target hardware resources, and verify the connection settings.

6. In the Simulink model, double-click the Audio File Read block. By default, the audio file specified is guitartune.wav. To play a different audio file, click Browse, and then select the required file from your computer. If the file that you select is a stereo file, remove the Vector Concatenate block from the model.

7. Double-click the ALSA Audio Playback block. In this model, the block sends the audio signal to the 'hw:0,0' audio device on the Raspberry Pi hardware. 'hw:0,0' is the default audio jack. To list the audio playback devices available on your Raspberry Pi hardware, enter the following commands in the MATLAB® command window.

r = raspberrypi;
a = r.listAudioDevices('playback')

The resulting structured array contains the names and numbers of the available audio playback devices on your Raspberry Pi hardware.

A sample output is shown here:

a(1)
    Name: ' bcm2835 - bcm2835 ALSA...'
  Device: '0,0'

a(2)
    Name: ' bcm2835 - bcm2835 ALSA...'
  Device: '0,1'

a(3)
    Name: ' USB-Audio - USB PnP Sound Device...'
  Device: '1,0'

This result indicates that three audio playback devices are available on the Raspberry Pi hardware. The ALSA audio device numbers are '|0,0|', '|0,1|', and '|1,0|'. The first two devices correspond to the analog audio output and the HDMI output of the Raspberry Pi hardware. The third device is a USB audio dongle. To use the playback device 0,0, double-click the ALSA Audio Playback block, and specify the Device name parameter as 'plughw:0,0'.

8. On the Hardware tab of the Simulink model, in the Mode section, select Run on board and then click Build, Deploy & Start. This action builds, downloads, and runs the model on the Raspberry Pi hardware. The audio starts playing, and the colored bars on the 8x8 LED matrix of Sense HAT are displayed in synchronization with the audio being played.

Other Things to Try

See Also