owen chang
Followers: 0 Following: 0
Estadística
9 Preguntas
0 Respuestas
CLASIFICACIÓN
37.544
of 293.501
REPUTACIÓN
1
CONTRIBUCIONES
9 Preguntas
0 Respuestas
ACEPTACIÓN DE RESPUESTAS
22.22%
VOTOS RECIBIDOS
1
CLASIFICACIÓN
of 20.033
REPUTACIÓN
N/A
EVALUACIÓN MEDIA
0.00
CONTRIBUCIONES
0 Archivos
DESCARGAS
0
ALL TIME DESCARGAS
0
CLASIFICACIÓN
of 148.733
CONTRIBUCIONES
0 Problemas
0 Soluciones
PUNTUACIÓN
0
NÚMERO DE INSIGNIAS
0
CONTRIBUCIONES
0 Publicaciones
CONTRIBUCIONES
0 Público Canales
EVALUACIÓN MEDIA
CONTRIBUCIONES
0 Temas destacados
MEDIA DE ME GUSTA
Feeds
Pregunta
why exportONNXNetwork will add additional "Sub" in onnx, how to remove this layer in onnx?
Hi, i did the following: >> baseNetwork = resnet50; >> exportONNXNetwork(baseNetwork,'resnet50-matlab'); but when compare sam...
casi 5 años hace | 1 respuesta | 0
1
respuestaPregunta
how to deploy deep learning prototype to FPGA using HDL Coder?
Hi i have FPGA platform and like to play around with Matlab deep learning (like MatConvNet), then deploy on my FPGA platform fo...
casi 7 años hace | 1 respuesta | 0
1
respuestaPregunta
running open_system('hdlcoder_led_blinking') for zynq, but no connection?
Hi, i am using usb jtag cable for communication with zynq-zc702, but i can't see serialport as instructed in the webinar, how sh...
casi 11 años hace | 1 respuesta | 0
1
respuestaPregunta
how could i generate an axi-stream or axi4-lite dma master by hdl coder?
Hi, i found the current demo using only axi-stream slave interface in sobel image processing system. however, it might require a...
casi 11 años hace | 1 respuesta | 0
1
respuestaPregunta
HDL Stream FFT in HDL Coder 2013b, not support AXI4-Stream Interface? (single rate?)
Hi, i have built a system involving Stream FFT with AXI4-Stream Interface, the goal is to put this design into Zynq, so AXI4-St...
casi 11 años hace | 1 respuesta | 0
1
respuestaPregunta
Failed Streaming interface is not supported when the DUT is not single rate
Hi, the AXI-Stream interface for Stream FFT is requiring DUT "single rate", but i can't find where to set it, and what does it ...
casi 11 años hace | 0 respuestas | 0
0
respuestasPregunta
HDL Stream FFT in HDL Coder 2013b, not support FPGA?
Hi, i am using Stream FFT for Zynq, but once i have created the subsystem and set it to Atomic, i have this error message pop u...
casi 11 años hace | 1 respuesta | 0
1
respuestaPregunta
How to create a FFT ipcore for Zynq using Simulink HDL Coder?
there is an error message "not support for frame based module"? is there any other solution for exporting signal processing bl...
casi 11 años hace | 2 respuestas | 1
2
respuestasPregunta
Does HDL coder from Simulink support AXI-4 Stream Interface for Xilinx Zynq?
Hi all, I have created an adder example and export to Xilinx Vivado 2013.2 using HDL coder, and integrated using Vivado IPI. th...
casi 11 años hace | 1 respuesta | 0