With the HDL Coder™ software, you can implement a simplified, streaming pixel protocol in your model. The software generates an HDL IP core with AXI4-Stream Video interfaces.
You can use the streaming pixel protocol for AXI4-Stream Video interface mapping. Video algorithms process data serially and generate video data as a serial stream of pixel data and control signals. To learn about the streaming pixel protocol, see Streaming Pixel Interface (Vision HDL Toolbox).
To generate an IP core with AXI4-Stream Video interfaces, in your DUT interface, implement these signals:
Pixel Control Bus
The Pixel Control Bus is a bus that has these signals:
The signals hStart and hEnd represent the start of an active line and the end of an active line respectively. The signals vStart and vEnd represent the start of a frame and the end of a frame.
You can optionally model the backpressure signal, Ready, and map it to the AXI4-Stream Video interface.
This figure is a 2–by–3 pixel image. The active image area is the rectangle with a dashed line around it and the inactive pixels that surround it. The pixels are labeled with their grayscale values.
This figure shows the timing diagram for the Pixel Data and Pixel Control Bus signals that you model at the DUT interface.
The Pixel Data signal is the primary video signal that is transferred across the AXI4-Stream Video interface. When the Pixel Data signal is valid, the valid signal is asserted.
The hStart signal becomes high at the start of the active lines. The hEnd signal becomes high at the end of the active lines.
The vStart signal becomes high at the start of the active frame in the second line. The vEnd signal becomes high at the end of the active frame in the third line.
This figure shows the timing diagram for the Pixel Data, the Pixel Control Bus, and the Ready signal that you model at the DUT interface.
When you map the DUT ports to an AXI4-Stream Video interface, you can optionally model the backpressure signal, Ready, and map it to the AXI4-Stream Video interface.
In a Slave interface, with the Ready signal, you can apply back pressure. In a Master interface, with the Ready signal, you can respond to back pressure.
If you model the Ready signal in your AXI4-Stream Video interfaces, your Master interface must deassert its valid signal one cycle after the Ready signal is deasserted.
If you do not model the Ready signal, HDL Coder generates the associated backpressure logic.
You can model your video algorithm with Pixel Data and Pixel Control Bus signals at the DUT ports and map the signals to AXI4-Stream Video interfaces. You can optionally model the backpressure signal, Ready, and map it to the AXI4-Stream Video interface.
This figure shows an example of a top-level Simulink® model with a Video Source input.
The Frame To Pixels and Pixels To Frame blocks perform the conversion between the video frames and the Pixel Data and Pixel Control Bus at the DUT interface. To use these blocks, you must have the Vision HDL Toolbox™ installed.
This figure shows how to model the Pixel Data and Pixel Control Bus signals inside the DUT subsystem.
You can directly connect the valid signal from the Pixel Control Bus to the Enable port. If you do not have the Vision HDL Toolbox software, replace the Pixel Control Bus Selector and Pixel Control Bus Creator blocks with the Bus Selector and Bus Creator blocks respectively.
The AXI4-Stream Video interfaces in your DUT can optionally include a Ready signal.
For example, you can have a FIFO in your DUT to store some video data before processing the signals. Use a FIFO Subsystem that contains HDL FIFO blocks to store the Pixel Data and the Pixel Control Bus signals. To apply the backpressure to the upstream component, model the Ready signal based on the FIFO Full signal.
This figure shows how to model the Ready signal inside the DUT subsystem.
The FIFO Subsystem block uses HDL FIFO blocks for the Pixel Data and for the Pixel Control Bus signals.
Disable delay balancing for the Ready signal path. If you enable delay balancing, the coder can insert one or more delays on the Ready signal.
When you run the
IP Core Generation workflow, you can map multiple
DUT ports to AXI4-Stream Video Master and AXI4-Stream Video Slave channels. The DUT
ports mapped to multiple interface channels must use scalar data type. When you use
vector ports, you can map the ports to at most one AXI4-Stream Video Master channel and
one AXI4-Stream Video Slave channel.
To learn more, seeGenerate HDL IP Core with Multiple AXI4-Stream and AXI4 Master Interfaces.
The HDL Coder software supports designs with multiple sample rates when you run the IP Core Generation workflow. When you map the interface ports to AXI4-Stream Video Master or AXI4-Stream Video Slave interfaces, to use multiple sample rates, ensure that the DUT ports that map to these AXI4 interfaces run at the fastest rate of the design after HDL code generation.
To learn more, see Multirate IP Core Generation.
Video capture systems scan video signals from left to right and from top to bottom. As these systems scan, they generate inactive intervals between lines and frames of active video. This inactive interval is called a video porch. The horizontal porch consists of inactive cycles between the end of one line and the beginning of next line. The vertical porch consists of inactive cycles between the ending active line of one frame and the starting active line of next frame.
This figure shows a video frame with the horizontal porch split into a front and a back porch.
The AXI4-Stream Video interface does not require a video porch, but Vision HDL Toolbox algorithms require a porch for processing video streams. If the incoming pixel stream does not have a sufficient porch, HDL Coder inserts the required amount of porch to the pixel stream. By using the AXI4-Lite registers in the generated IP core, you can customize these porch parameters for each video frame:
Active pixels per line (Default: 1920)
Active video lines: (Default: 1080)
Horizontal porch length (Default: 280)
Vertical porch length (Default: 45)
You can integrate the generated HDL IP core with AXI4-Stream Video interfaces into the
Default video system reference design.
This figure is a block diagram of the
Default video system
reference design architecture.
You can use this
Default video system reference design
architecture with these target platforms:
Xilinx Zynq ZC702 evaluation kit
Xilinx Zynq ZC706 evaluation kit
To use the
Default video system reference design, you must
install the Support Package for Vision HDL Toolbox Support Package for Xilinx®
When you map the DUT ports to AXI4-Stream Video interfaces:
The DUT port mapped to the Pixel Data signal must use a scalar data type.
Xilinx Zynq-7000 must be your target platform.
You must use Xilinx Vivado® as your synthesis tool.
Processor/FPGA synchronization must be