Points inside multiple polygon for contour
21 visualizaciones (últimos 30 días)
Mostrar comentarios más antiguos
Tessa Kol
el 29 de Sept. de 2020
Comentada: Tessa Kol
el 29 de Sept. de 2020
I made the following contourplot.
Then, I plot discretized points over this plot.
I wanted to find the (x,y) coordinates of the discretized points within the region between the boundaries 40.94 and 43. This is the way how I approached it. With contourtable I acquired the (x,y) coordinates of the contourlines.
muSP = [0.1,0.2,0.3,0.4,0.5,0.6,0.7,0.8,0.9];
muRP = [0.1,0.2,0.3,0.4,0.5,0.6,0.7,0.8,0.9];
[X,Y] = meshgrid(muSP,muRP);
Z = cell2mat(reshape(AoR_mean,[9,9]));
[C,h] = contour(X,Y,Z,(40.9431:2.0538:42.9969));
hold on
title('Angle of Repose - Ledge Test 2D');
xlabel('\mu_s')
ylabel('\mu_r')
clabel(C,h,'LabelSpacing',500,'FontSize',8);
h.LevelList = round(h.LevelList,2);
set(gca,'XTick',0.1:0.1:0.9,'XTickLabel',0.1:0.1:0.9,'XTickLabelRotation',45);
set(gca,'YTick',0.1:0.1:0.9,'YTickLabel',0.1:0.1:0.9);
grid on
% Extract x- and y-coordinates of contour lines
contourTable = getContourLineCoordinates(h);
% Define grid for the variable space
N1 = 80;
muRP_grid = linspace(0.1,0.9,N1);
muSP_grid = linspace(0.1,0.9,N1);
[R,S] = meshgrid(muRP_grid,muSP_grid);
plot(R,S,'.r');
hold off
% x- and y-coordinates of polygon vertices, i.e. between AoR of 40.11 degrees
% and AoR of 43.83 degrees
xv = table2array(contourTable(1:31,3));
yv = table2array(contourTable(1:31,4));
inside_variablespace = inpolygon(R,S,xv,yv);
% x- and y-coordinates corresponding to the discretized points in the
% variable spac
xcoord = R(inside_variablespace);
ycoord = S(inside_variablespace);
However, for some reason I don't get de discretized points within the boundaries 40.94 and 43.
0 comentarios
Respuesta aceptada
KSSV
el 29 de Sept. de 2020
Read about inpolygon. If you have a polygon and a set of points, you cann extract the points lying inside this polygon using that.
8 comentarios
Adam Danz
el 29 de Sept. de 2020
Editada: Adam Danz
el 29 de Sept. de 2020
Check out the examples in the documentation
You can call inpolygon on the outer polygon, then call inpolygon on the inner polygon, then remove selected points that are in both.
Example
A = inpolygon(...)
B = inpolygon(...)
A(B) = false;
Use these answers as a stepping stone rather than looking for full solutions.
Más respuestas (1)
Ameer Hamza
el 29 de Sept. de 2020
There is no need to use inpolygon here. You can directly create a mask from the Z matrix. Following shows an example, and find the x and y coordinates from the mesh between contour lines at 0.33 and 0.66
[X, Y] = meshgrid(linspace(-1, 1));
Z = X.^2 + Y.^2;
levels = [0 0.33 0.66 1]; % levels for contour plot
mask = Z < 0.66 & Z > 0.33;
x_coord = X(mask);
y_coord = Y(mask);
contour(X, Y, Z, levels)
hold on
plot(x_coord, y_coord, '+')
4 comentarios
Ameer Hamza
el 29 de Sept. de 2020
What is the error. In the data you shared, AoR_mean is undefined, so I cannot run your code to see the issue.
Ver también
Categorías
Más información sobre Map Display en Help Center y File Exchange.
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!