Nick Choi
Followers: 0 Following: 0
Estadísticas
0 Preguntas
55 Respuestas
0 Problemas
2 Soluciones
CLASIFICACIÓN
656
of 289.966
REPUTACIÓN
108
CONTRIBUCIONES
0 Preguntas
55 Respuestas
ACEPTACIÓN DE RESPUESTAS
0.00%
VOTOS RECIBIDOS
16
CLASIFICACIÓN
of 19.612
REPUTACIÓN
N/A
EVALUACIÓN MEDIA
0.00
CONTRIBUCIONES
0 Archivos
DESCARGAS
0
ALL TIME DESCARGAS
0
CLASIFICACIÓN
73.411
of 144.350
CONTRIBUCIONES
0 Problemas
2 Soluciones
PUNTUACIÓN
30
NÚMERO DE INSIGNIAS
1
CONTRIBUCIONES
0 Publicaciones
CONTRIBUCIONES
0 Público Canales
EVALUACIÓN MEDIA
CONTRIBUCIONES
0 Temas destacados
MEDIA DE ME GUSTA
Feeds
Resuelto
Make the vector [1 2 3 4 5 6 7 8 9 10]
In MATLAB, you create a vector by enclosing the elements in square brackets like so: x = [1 2 3 4] Commas are optional, s...
más de 1 año hace
Rapid Accelerator Mode fatal error C1128
You can add '/bigobj' to the compiler options in the 'Code Generation' pane of the 'Configuration Parameters' in Simulink to a...
más de 6 años hace | 2
| aceptada
PWM generation - triangle carrier problem
It is tough to say without a reproduction model but this could be due to differing sample times between the two signals going in...
más de 6 años hace | 0
generating square wave to control a motor without using simulink
The 'writePWMDutyCycle' function in the MATLAB Support Package for Arduino would allow you to control the duty cycle/pulse width...
más de 6 años hace | 0
change the modulation in commrfsatlink
The following section of the example page provides information on how some of the model's parameters can impact the performance ...
más de 6 años hace | 0
using a table in a "from workspace block" in simulink
If the data is loaded into MATLAB as a table, you could import the signal data using a 'From Workspace' block on the column or r...
más de 6 años hace | 0
Update a fixed dimension vector Simulink
A block that may be helpful for this could be the 'Assignment' block: <https://www.mathworks.com/help/simulink/slref/assignme...
más de 6 años hace | 0
| aceptada
I have no idea how to do this simulink, please help
Figure 1 shows you what the model should look like so you essentially just need to reconstruct that model in Simulink. This ...
más de 6 años hace | 0
What is the computation Power of Matlab Online?
The following documentation pages should help give you a better idea of what tasks can be performed using MATLAB Online. Thi...
más de 6 años hace | 0
Simulink Real Time/Simulink Test using National Instruments RT hardware?
Simulink Test allows you to develop and execute simulation-based tests for your Simulink models and these tests can be run with ...
más de 6 años hace | 0
Use of soundcard in Simulink!
The 'Audio Device Reader' block in the Audio System Toolbox would allow you to read audio from your computer's sound card. The f...
más de 6 años hace | 0
| aceptada
How do i create a simplified version of a continuous time unit step function?
The following example shows how to create a variety of signals such as the unit impulse, unit step and unit ramp signals: <ht...
más de 6 años hace | 0
How to input a signal to a Simulink Function within a Stateflow Chart?
Based off of the error message, it seems as though the function call block is set to have a sample time of zero. Since the input...
más de 6 años hace | 0
Implementing neural network functions on HDL
The following documentation page provides a list of the MATLAB functions that are supported for HDL code generation: <https:...
más de 6 años hace | 1
| aceptada
Activate a pulse generator from an if block
You could use a 'Compare to Constant' block to compare the signal/variable against the specified value and this could be used to...
más de 6 años hace | 0
Difficulty using the CWT function
It seems as though the error messages are being generated because the new and old versions of the 'cwt' function are being calle...
más de 6 años hace | 0
How can I find Model-Based Calibration Toolbox in MATLAB 2017b?
Is 'Model-Based Calibration Toolbox' displayed when you execute the following command? >> ver If it is not displayed by...
más de 6 años hace | 0
| aceptada
Missing simscape power systems
Is 'Simscape Power Systems' displayed when you execute the following command? >> ver If it is not displayed by the 'ver...
más de 6 años hace | 1
Simulink name logged runs
You can name a run with a string to facilitate data inspection by utilizing a function call similar to this one: Simulink.s...
más de 6 años hace | 0
How to model a slack(swing) bus in simuilink model?
The 'Load Flow Bus' block can be used to specify the parameters of a swing bus: <https://www.mathworks.com/help/physmod/sps/pow...
más de 6 años hace | 0
How to solve "No rule to make target `rtiostream_utils.c' " error while building model in Simulink?
Without a reproduction model or screenshots of the entire error, it is somewhat difficult to determine a potential root cause. H...
más de 6 años hace | 0
How can I pass a Figure Handle to Matlab code embedded in Simulink, and capture that plot as an Image in the loop?
If you are planning to generate code from the Simulink model, you will not be able to use the 'plot' function because it is not ...
más de 6 años hace | 0
R2017b Visual Studio 2017 can't link model files when compiling simulink
This issue seems like it may be related to the following external bug report: <https://www.mathworks.com/support/bugreports/1...
más de 6 años hace | 0
| aceptada
Understanding usrpe3xxToneReceiverML.m example
In the 'Transmit a Tone Signal from the FPGA' section of the example, there is a line that says "Note that the simultaneous tran...
más de 6 años hace | 0
I have successfully generated the code from the matlab, but I don't kown how to use these codes in the embedded equipment.
When you generate C/C++ code through MATLAB Coder, you can specify the target platform for the code and you can configure it to ...
más de 6 años hace | 0
| aceptada
put coodinate in image map
The following documentation page provides an example of how to display topographic data in MATLAB: <https://www.mathworks.com/h...
más de 6 años hace | 0
| aceptada
How can I force a Custom Storage class for a parameter inside StateFlow?
If you are looking for how to use custom storage classes or custom data types in Simulink, the following documentation link prov...
más de 6 años hace | 0
Hou to make a simulink lookup table model for different break point?
Simulink comes with several shipped lookup table blocks. The following documentation page contains a list of the various lookup ...
más de 6 años hace | 0
How can explain the relation between mdlDerivatives output and mdlOutputs in S-function simulink
As described in this documentation link, 'mdlDerivatives' is an optional method that can be used to compute the derivatives for ...
más de 6 años hace | 1