photo

Aquatris


Last seen: 24 días hace |  Con actividad desde 2023

Followers: 3   Following: 0

Estadística

All
  • 6 Month Streak
  • Knowledgeable Level 4
  • Community Group Solver
  • Solver
  • First Answer

Ver insignias

Feeds

Ver por

Respondida
What are the names of these blocks in the current Simulink r2024b
My guess: First one is a ramp block, second one is a step block, third one is a step block again but the step is done from time ...

27 días hace | 0

Respondida
Hello everyone, how can use matpower with the online matlab?
You upload the matpower.m to your matlab drive and work like that.

alrededor de 2 meses hace | 0

| aceptada

Respondida
6x6 system of multivariate quadratic equations ... non-negative real solutions
fsolve seems to work for most cases, if not lsqnonlin is also an option. here is a general explanation

alrededor de 2 meses hace | 1

Respondida
How can i define xo or intial parameters that the ga begin with ?
You use InitialPopulationMatrix of optimoptions. You can get more info on what options you can set for ga in here under InputArg...

alrededor de 2 meses hace | 0

Respondida
finding relation between two variables, being discharge and water level in a river
Here is another way using unconstarint optimization: % define some parameters c_real = 3.2965;% actual c value in q = h^c h_m...

alrededor de 2 meses hace | 0

Respondida
Configure model block in simscape
In simulink you can create masked systems with parameters and attach a callback to those parameters. So in the callback you can ...

alrededor de 2 meses hace | 1

Respondida
Unable to connect scope wit circuit output
You need to put a block for what you want to measure at that point, you can use voltage sensor block to measure the voltage and ...

alrededor de 2 meses hace | 0

Respondida
How to create a state space model with constant term and do feedback.
You can define which inputs and outputs are connected to your controller. Checkout the feedback function page and look at the 'S...

2 meses hace | 0

Respondida
How to merge two tables into a single table?
You can add "Source" header to each table with "Table 1" or "Table 2" inputs and join them like joining arrays; table1 = table(...

2 meses hace | 1

Respondida
Conditionally stop simulation in simulink
You can use the stop simulation block.

2 meses hace | 0

Respondida
function zpk and linmod
Here explains how it is done. Basically you have your function that describes the relation between states and inputs. If they ar...

2 meses hace | 0

Respondida
How to calculate Average without receiving 'Inf' as a result.
Here is one way: % create dummy matrix A = rand(100,1); A([5 10 24 55 23 60]) = inf; A([12 56 29 35]) = nan; mean(A) % s...

2 meses hace | 0

Respondida
writematrix: how to get formatted txt-output?
Use 'tab' delimiter option instead of single space. M = [100 0 4500;0 1 38.29;1 1 38.22]; writematrix(round(M,2),'file.txt',...

3 meses hace | 0

Respondida
Simulate recursive function in simulink
I did not care about the dimensions at all while creating the simulink model so some adjustment might be necessary but this is o...

3 meses hace | 0

Respondida
Add NaN in the first row of a table
Assuming all your entries are numeric, since you want to assign NaN, here is one way; % create dummy table Age = [38;43;38;40;...

3 meses hace | 0

Respondida
Error in displaying the whole matrix
Ther eis probably a 1e6 at the top of the display. You can do 'format bank' to mitigate this if you want or any other format opt...

4 meses hace | 0

| aceptada

Respondida
How to update a function with output from another function?
Here is one way iff the required variables are within the state vector 'y', then you can do: %% change ode45 call [t, y] = ode...

4 meses hace | 0

Respondida
slow drawing of a set of points on a plane
In essence for loop are always slower. So try to vectorize your code whereever possible for efficiency, here is a good read. In ...

4 meses hace | 0

| aceptada

Respondida
plot magnitude data at location (x,y,z)
Here is one way where you use colors to indicate the magnitude; % random data x = [0:pi/50:10*pi nan]; % nan is added to remov...

4 meses hace | 0

Respondida
Generate the motion (Trajectory) of a sphere (or point) with given velocity value
If you dont care about the actual timing and things, here is one way where the colors of the path indicate the speed and a simpl...

4 meses hace | 0

Respondida
How to generate vector with non-linear spacing?
The answer from another question here: A = 1; B = 5; std = .9; % need to play with this to get desired shape within desired r...

4 meses hace | 0

Respondida
Second Order Laplace solving doesn't work ('Unable to find explicit solution')
Not sure the underlying reason behind it but you are defining the X as a function of s and solve function seems to be having tro...

4 meses hace | 0

| aceptada

Respondida
How do I solve system of differentials using ode45 and eom functions
You defined a symbolic variable within your ode function, which is a nono if you wanna solve it numerically :D function ds = e...

5 meses hace | 1

| aceptada

Respondida
Solving with ode45 with a solution dependant variable in the ode
No, you should not do it that way. Instead you should create your function properly in a way that represents the equations. It w...

5 meses hace | 0

Respondida
How to display a color bar in Matlab as shown below
You can call the colorbar function with the desired tick values Z = peaks; contourf(Z) colorbar('ticks',[-6:0.5:8])

5 meses hace | 1

Respondida
Error in for loop: Index exceeds matrix dimensions.
You have essentially made two mistakes: matrix_f only has 6 rows. You setup up your for loop such that k is 1 2 3 4 5 6 . When ...

5 meses hace | 0

| aceptada

Respondida
Friend Function implementation in MATLAB
You can use the Access List property. Here is more explanation. Here also.

5 meses hace | 0

Respondida
how to do rising and falling edge in single signal using signal builder..?
Click on Signal->ReplaceWith or New->Square and play with the points. Alternatively, click on Signal->Custom-> enter your time...

5 meses hace | 1

| aceptada

Respondida
how to make task in simulink
You can specify sample time of each block seperatly. Here is more information and how to do it for different blocks, subsystems ...

5 meses hace | 0

Respondida
How to loop through cell array and apply script to each double?
You can use the cellfun function, where you use your script as the function. Example: a = {1:3, 200:205, 10:12}; new_a = cell...

5 meses hace | 0

Cargar más