dimitris


Con actividad desde 2011

Followers: 0   Following: 0

Mensaje

Estadística

  • 3 Month Streak
  • Thankful Level 3
  • First Answer

Ver insignias

Feeds

Ver por

Pregunta


Genetic algorithm initial popuplation
I use GA to minimize an objective function with 20 variables. I noticed that ga always produces initial population with small di...

más de 11 años hace | 2 respuestas | 0

2

respuestas

Pregunta


Sensitivity of a timer
I use a timer block and observed that if the time values are too close, they do not appear in the scope. For example if time is ...

más de 11 años hace | 0 respuestas | 0

0

respuestas

Pregunta


Speeding up exhaustive search
I need to find the global minimum of a function using exhaustive search. I have 10 function variables x1,x2,x3,...,x10 ∈ [0,10]...

más de 11 años hace | 2 respuestas | 0

2

respuestas

Respondida
I want to determine whether the user wishes to work with their angles in degrees or radians
type= input('Enter D to work angle in degrees or R for radians') V= input('Enter velocity '); a= input('Enter angle ')...

más de 11 años hace | 0

Respondida
Warnings and error produced by simulink
The solution is to disable the zero crossing detection for the whole system.

más de 11 años hace | 0

| aceptada

Respondida
variables in Simulink Workspace
Simulink resolves variables from base workspace, so if you use simout from a function it wont be able to 'see' it because functi...

casi 12 años hace | 0

Pregunta


Warnings and error produced by simulink
I try to optimize a measurement from simulink model using the ga function. The optimization runs well for some generations excep...

casi 12 años hace | 2 respuestas | 0

2

respuestas

Pregunta


About termination of genetic algorithm
I have set the options of the ga as shown: options=gaoptimset(options,'Generations',100); The algorithm terminates after...

casi 12 años hace | 2 respuestas | 0

2

respuestas

Pregunta


How to measure the phase difference between two signals in simulink?
I have two signals in my circuit and i would like to measure the phase difference between them. Is there a block i could use? If...

casi 12 años hace | 3 respuestas | 0

3

respuestas

Pregunta


How to hide warnings ?
I do not want warnings to appear when i execute my code but i do not want to turn them off as well. Is this possible?

alrededor de 12 años hace | 3 respuestas | 0

3

respuestas

Respondida
Problem
You pass an argument of type "char" to function tc_cmdq and this function does not take input of this type.

alrededor de 12 años hace | 0

Pregunta


Genetic algorithm: child out of constraints
I have set the linear inequality constraints of the GA in a way that each gene is smaller than the next one, eg x1<x2<x3...<xn b...

alrededor de 12 años hace | 1 respuesta | 0

1

respuesta

Pregunta


Time values must be monotonically increasing error
In my simulink model i use a from workspace block to read some time values and alhough those values are increasing i get the err...

alrededor de 12 años hace | 1 respuesta | 1

1

respuesta

Respondida
Problem with sim command
If i understood what you mean, your problem is that for some values you get an error. In this case you can set your constraints ...

alrededor de 12 años hace | 0

Pregunta


From workspace block error
I run the following code : wave.time=t; wave.signals.values = val; wave.signals.dimensions=1; where t and val are vectors. I...

alrededor de 12 años hace | 1 respuesta | 1

1

respuesta

Pregunta


Simulink and linux
When i try to open a simulink model i get the error: MATLAB:dispatcher:loadLibrary Can't load ~/Matlab2011bu/bin/glnxa64/libm...

más de 12 años hace | 1 respuesta | 1

1

respuesta

Pregunta


Problem with gaoptimset in unix
I have a problem runing my code in unix although the same code is running in windows. The error i get is the following: "Undefin...

más de 12 años hace | 1 respuesta | 0

1

respuesta

Pregunta


Problem with matlab function block.
I use a matlab function block in my simulink model and when i read a variable(for example N) from a file i get an error, but if ...

más de 12 años hace | 2 respuestas | 0

2

respuestas

Pregunta


What does '@' mean in a matlab expression?
For example [x,y] = foo1(@(x) foo2(x),z); Thank you in advance for your help.

más de 12 años hace | 1 respuesta | 2

1

respuesta

Pregunta


Steady state?
I am building a circuit with simulink and i was wondering if the results i take are in steady state. Are the elements in simulin...

más de 12 años hace | 1 respuesta | 0

1

respuesta

Pregunta


How i choose the best solver ?
How i choose the best solver for my simulink model and why i get different results if i use a different solver?

más de 12 años hace | 1 respuesta | 0

1

respuesta

Pregunta


mxArray problem
In a simulink model I use a matlab function block in which i open a file(fopen), read some numbers(fscanf) and put them in an ar...

más de 12 años hace | 3 respuestas | 0

3

respuestas