Estadística
0 Preguntas
794 Respuestas
57 Archivos
CLASIFICACIÓN
132
of 301.522
REPUTACIÓN
948
CONTRIBUCIONES
0 Preguntas
794 Respuestas
ACEPTACIÓN DE RESPUESTAS
0.00%
VOTOS RECIBIDOS
157
CLASIFICACIÓN
8 of 21.315
REPUTACIÓN
45.261
EVALUACIÓN MEDIA
4.70
CONTRIBUCIONES
57 Archivos
DESCARGAS
1845
ALL TIME DESCARGAS
371783
CLASIFICACIÓN
of 175.118
CONTRIBUCIONES
0 Problemas
0 Soluciones
PUNTUACIÓN
0
NÚMERO DE INSIGNIAS
0
CONTRIBUCIONES
0 Publicaciones
CONTRIBUCIONES
0 Público Canales
EVALUACIÓN MEDIA
CONTRIBUCIONES
0 Temas destacados
MEDIA DE ME GUSTA
Feeds
vehicle dynamics code problems
Hi Bradford - I was unable to reproduce this error message. Normally, that means the variable t is not defined in the scope wer...
2 meses hace | 0
Where can I find the V2Glib library for Simulink?
That library was renamed to renamed to VehicletoGridSystemLib.slx. It is part of an example. In R2025a or earlier, run this co...
5 meses hace | 0
Kann man in Simscape ein Feder-Stößel-System simulieren
Es ist nicht genau dasselbe, aber dieses Beispielmodell, das mit Simscape Multibody geliefert wird, ist sehr ähnlich. https://w...
11 meses hace | 0
Simulation of crystal oscillator circuit a Simscape does not converge
While I can't say for sure what is going wrong, if I set Rf to 1e9 the simulation runs to completion and the value on the Scope ...
alrededor de 1 año hace | 0
How do i know which switch should i use in Simulink?
To use Simulink signals to control inputs to Simscape blocks, you often need this converter block https://www.mathworks.com/hel...
alrededor de 1 año hace | 0
| aceptada
Does MATLAB have four in-wheel motor Electric vehicle model, where one motor control one wheel independently. Sometimes called 4-Indepdendent Drive EV, 4 In-wheel motor EV
Take a look at this File Exchange submission: https://www.mathworks.com/matlabcentral/fileexchange/172279-formula-student-vehic...
más de 1 año hace | 0
How to check with different C rates of battery model in Simulink
To modify the C rate, you will need to modify the level of current drawn from the battery. You can use a Controlled Current Sou...
más de 1 año hace | 0
I am trying to implement Li-Ion battery model in Simulink. I want to measure temperature inside model in real-time and also figure out changes in it with variable voltage supply. Can anyone give me reference of this model and how to simulate it ??
I recommend you look at the Battery Pack Builder in Simscape Battery. It helps you assemble battery packs and construct a test ...
más de 1 año hace | 0
Battery soc is not working as expected in different file it shows different variation in soc can any one help this out ...
The parameters are only a portion of what affects the SOC during a simulation. The systems on the grid, test profile, and solve...
más de 1 año hace | 0
V2G matlab exemple
In https://www.mathworks.com/help/sps/ug/24-hour-simulation-of-a-vehicle-to-grid-v2g-system.html, the scopes are plotting the ac...
más de 1 año hace | 0
In simscape for lead acid battery cell how can i calculate and assign values for main branch and paracetic branch values
Typically you would obtain measurement data and use parameter estimation techniques. Take a look at this example to see the pro...
más de 1 año hace | 0
Simscape Torque Sensor output is zero
Your angular motion sensor should be connected between shaft and a Mechanical Rotational Reference (NOT in series). Your torque...
alrededor de 2 años hace | 1
| aceptada
Does anyone know why I get an error when I run the fuel cell model for about 18000s?
The error message you encountered is because the test conditions for the fuel cell are not suitable for 18000 seconds. The driv...
más de 2 años hace | 1
How to avoid adding the striking mass to the robot body mass during a collision test in simscape?
A really good way to do this is to use Simscape Multibody. With Simscape Multibody you can model contact forces between differe...
más de 2 años hace | 0
Battery box in Simscape
Hi Bence, You can model a housing for your battery modules that prevents heat transfer between the modules. This could be pass...
más de 2 años hace | 0
| aceptada
Add a Simscape Multibody model to a Simscape Electrical model
Hi all, In R2021a we added interface blocks to more easily connect Simscape Multibody joints to 1D mechanical Simscape networks...
más de 2 años hace | 1
Workflow to combine CAD Model and SIMSCAPE Thermal transient Analysis
You should be able to obtain distance measurements using sensors, assign them to a Simulink signal (or Simscape Physical Signal)...
más de 2 años hace | 0
Mechanical rotational port of Induction Motor from the specialized power system library
I believe you need to remove the Mechanical Rotational Reference. You have essentially welded the shaft to the earth so it cann...
más de 2 años hace | 0
simscape (planetary gear)
The planetary gear enforces a kinematic relationship between the input and output shafts. The torque levels, however, will depe...
más de 2 años hace | 1
| aceptada
Friction and wear Simulink model for brake pad application
Take a look at the Simscape Driveline Disc Brake block https://www.mathworks.com/help/sdl/ref/discbrake.html This example ...
casi 3 años hace | 0
Testing of disc brakes
The parameters you describe match well with the Simscape Driveline Disc Brake block https://www.mathworks.com/help/sdl/ref/...
casi 3 años hace | 0
How can I implement the magic formula by Pacejka in Simscape Multibody between a wheel modeled as a disk and the ground modeled as a prismatic piece?
You can look at File Exchange submission Spatial Contact Force Examples Simscape Multibody to see an example of how to add a cus...
casi 3 años hace | 0
Problem by simulating a kinematic with a singularity in SimMechanics
This message indicates you have a degree of freedom with no inertia associated with it. I was not able to download your model, ...
casi 3 años hace | 0
water tank modeling in simscape
This example shows many of those concepts: https://www.mathworks.com/help/hydro/ug/aircraft-fuel-supply-system-with-three-t...
casi 3 años hace | 1
Frictional Friction block on simscape
In the Translational Friction block, set the coulomb friction force to be mu_k*(mass*gravity). Set the Breakaway Friction Force...
casi 3 años hace | 0
An error: Undefined function 'mrdivide' for input arguments of type 'NetworkEngine.ComponentVariableCompileData'.
The documentation page for equations in Simscape tells you which equations you can use and what the requirements are. mrdivide ...
casi 3 años hace | 0
Simulink Simscape: Dog Clutch fidelity
The Dog Clutch block in Simscape Driveline has multiple fidelity levels for the friction model. It can capture behavior when th...
casi 3 años hace | 0
How can I implement downforce and drag generated from a rear wing into my drag racing model using Simulink/Simscape?
If you wish to mak the downforce increase with speed, one option is to multiply it by a scaling factor that is speed dependent. ...
casi 3 años hace | 0
How can I use Translational Friction and Damping blocks?
I recommend placing a Revolute Joint between your two plates and add a rotational frictional model there. If you wish to model ...
casi 3 años hace | 0
