Estadística
0 Preguntas
16 Respuestas
CLASIFICACIÓN
5.064
of 300.364
REPUTACIÓN
10
CONTRIBUCIONES
0 Preguntas
16 Respuestas
ACEPTACIÓN DE RESPUESTAS
0.00%
VOTOS RECIBIDOS
1
CLASIFICACIÓN
of 20.934
REPUTACIÓN
N/A
EVALUACIÓN MEDIA
0.00
CONTRIBUCIONES
0 Archivos
DESCARGAS
0
ALL TIME DESCARGAS
0
CLASIFICACIÓN
of 168.407
CONTRIBUCIONES
0 Problemas
0 Soluciones
PUNTUACIÓN
0
NÚMERO DE INSIGNIAS
0
CONTRIBUCIONES
0 Publicaciones
CONTRIBUCIONES
0 Público Canales
EVALUACIÓN MEDIA
CONTRIBUCIONES
0 Temas destacados
MEDIA DE ME GUSTA
Feeds
LUT-based IPMSM Reference Block: Flux-Weakening Id/Iq Too High vs MotorCAD (R2025a)
Hi Adhavan, Thanks for the response. I assume this is the same data as what was shared in the technical escalation. More details...
alrededor de 1 mes hace | 0
Maximum Torque Per Voltage(MTPV) control of an IPMSM Power Drop issue in Deep Flux weakening Areas
Hi @PRATHEESH S, For implementing MTPV beyind FW region of operation (wherever it is possible depending on the motor's paramet...
alrededor de 1 mes hace | 0
how can we plot the voltage trajectory of pmsm motor , when we have vd and vq data from simulink?What kind of plot is this?
Hi, PMSM has multiple characteristic curves usually drawn on id-iq plane (Currnet limit curve, voltage limit curve, mtpa curve,...
12 meses hace | 0
Creating a 2D Lookup Table for PMSM in EV Applications Using Simulink
Hi, For collecting the data, please run the motor from a coupled motor at constant speed and maintain the load torque to captur...
alrededor de 1 año hace | 0
MTPA IN IPMSM Performance
Hi, reducing the id will effectively bring down the stator-rotor flux linkage. This results in reduced torque output in some con...
alrededor de 1 año hace | 0
Kindly tell me if the code (MTPA) is wrong for calculating MTPA curve
You can use the commandline utilities that are shipped with Motor Control Blockset. Please refer to the following links to explo...
alrededor de 2 años hace | 0
Challenges with Delta Wound Motor in Torque Control: Seeking Guidance on MTPA Reference Block for reference Id and Iq generation.
Hi Aditya, In addition, check the following link for using delta parameters for a motor plant model. One of the options (the...
alrededor de 2 años hace | 0
to obtain contour plots
You can use the commandline utilities that are shipped with Motor Control Blockset. Please refer to the following links to explo...
más de 2 años hace | 0
Using Ld and Lq inductance values for IPMSM
Additionally, you may also use the Ld Lq and fluxPM values using the blocks MTPA Control Reference and LUT based PMSM Control Re...
más de 2 años hace | 0
| aceptada
about the contour plots
To plot the constant torque contours and also other constraint curves of a PMSM, please refer to the following link. PMSM Cons...
más de 2 años hace | 0
How to draw MTPA curve on torque contours
To know how to draw the MTPA curves, and also other constraint curves of the PMSM, pls refere to the following link. PMSM Cons...
más de 2 años hace | 0
To calculate the max speed which can be achieved in field weakening region
A recent update to the Motor Control Blockset introduced few utilities to address these. PMSM Drive Characteristics and Constr...
más de 2 años hace | 0
can you provide me a file about flux weakening model of PMSM in simulink ?
In addition to the above suggested block, you may also use MTPA Control Reference or LUT based PMSM Control Reference blocks. To...
más de 2 años hace | 0
Field-Weakening Control (with MTPA) of PMSM
Hi You can refer to the following link to know the the principles behind the MTPA curve of a PMSM, and find how to plot them. ...
más de 2 años hace | 0
LUT based PMSM control reference ; Vdc input method
To add to the above answer, the 3D LUT option creates a 3D table for both id, iq values that depend on three parameters, namely,...
más de 2 años hace | 1
| aceptada
Torque control of PMSM motor- Need help
Hi, The torque setpoint can be derived using the PI controller based on the speed setpoint and the speed feddback value. You ma...
alrededor de 3 años hace | 0
