Hossam Mosbah

Last seen: casi 2 años hace | Con actividad desde 2014

Followers: 0 Following: 0

Mensaje

Hi everyone, I have a question?. I have created net1, net2, and net3 and all of these nets have the same inputs and targets with also different training algorithms and hidden-layers, however every nets has different outputs with different MSE, regression, and MAPE, so my question is how to connect these three nets by serial once and by parallel once. Thanks in advance. Professional Interests: Neural Network

Estadística

Ver insignias

Feeds

Pregunta

issue with matlab function
Matlab function did not store the previous vectors, it is only store the current vector and replace it other vectors by zeros? T...

más de 3 años hace | 1 respuesta | 0

1

respuesta

Pregunta

how to make figure that shown below
Hi everyone, I want to draw this figure and the olors keep overlapping, so is there any help so I can draw the figure withou...

más de 3 años hace | 1 respuesta | 0

1

respuesta

Pregunta

how to un-share scope in matlab
Hi all. I am having an issue with matlab, when i plot vector in workspace, it automatically open the scope in siumlink. I do...

más de 3 años hace | 1 respuesta | 0

1

respuesta

Pregunta

How to determine the exact intersection between line and two curves
Data is attached. Hi everyone, I am trying to find the exact intersection between line and curve and I tried everything and ...

casi 4 años hace | 2 respuestas | 0

2

respuestas

Pregunta

How to coordinate the power resources based on the cheapest cost using optimization based problem in matlab.
Hi all, I am working on optimization of several resources and using problem based optimization method. so I have this constrain...

más de 4 años hace | 1 respuesta | 0

1

respuesta

Pregunta

how to convert if condition into problem based approach in optimization problem
I have the problem below and I need to convert to problem based approach optimization problembecause I can not use if co...

más de 4 años hace | 0 respuestas | 0

0

respuestas

Pregunta

how to write this equation in matlab
I am trying to write this equation in matlab, so this is what I wrote, but it is always give me the minimim range prob.Constr...

casi 5 años hace | 0 respuestas | 0

0

respuestas

Pregunta

does anyone know how to draw straight line with curve in the same figure
Hi all, the curve for the load profile and the both straight lines are the shaving (peak and valley). I am trying to plot ...

casi 5 años hace | 1 respuesta | 0

1

respuesta

Pregunta

Does anyone know how to get the values of the variables?
I implemented the optimization problem below and I want to know the optimal values for c, P_shave, P_ess, soc, and P_grid. These...

casi 5 años hace | 1 respuesta | 0

1

respuesta

Pregunta

How can i obtain the final value of x and y?
How can i obtain the final value of x and y. both of x and y are variables? I am looking to get the final value (optimal values...

casi 5 años hace | 1 respuesta | 0

1

respuesta

Pregunta

Does anyone know how to modify this program for peak load shaving using charging and discharging battery
I am tryint to modify this code to shave the profile_load by energy storage battery (charging / discharging). The figure below t...

casi 5 años hace | 0 respuestas | 0

0

respuestas

Pregunta

how to convert matrix with arrays into vector
I have this type of matrix (2,1) 1.1348 (5,1) 0.49237 (1,2) 1.1348 (3,2) 0.6...

más de 8 años hace | 1 respuesta | 0

1

respuesta

Pregunta

How to set the input and target in power state estimation using neural network?
I am doing an experiment on power system state estimation using neural network for IEEE 14 bus system with fully observed. Full...

más de 9 años hace | 1 respuesta | 0

1

respuesta

Pregunta

how to vary white noise in data settle in matrix
I want to vary white noise by 5% each time and I want this variation to have an impact on the output error of neural network. If...

más de 9 años hace | 1 respuesta | 0

1

respuesta

Pregunta

error using fuzzy interface
x = (0:0.1:10)'; y = sin(2*x)./exp(x/5); trnData = [x y]; numMFs = 5; mfType = 'gbellmf'; outmfType='linear'; ...

casi 11 años hace | 0 respuestas | 0

0

respuestas

Pregunta

question is how to connect these three nets by serial once and by parallel once.
Hi everyone, I have a question?. I have created net1, net2, and net3 and all of these nets have the same inputs and targets wit...

alrededor de 11 años hace | 1 respuesta | 0

1

respuesta