- SBML compatibility. SBML requires that all species that appear in a reaction rate must appear as reactants and/or products. If you skip this step in SimBiology and create an SBML file, then the file will not pass the strictest levels of validation.
- Stochastic solver support. If you want to use one of SimBiology's stochastic solvers, then all reactions must be mass action, and all participating species must be included in the list of reactants and/or products (since SimBiology uses this information to construct an appropriate reaction rate).
Simbiology reaction stoichiometry: R + E ==> P + E, or the simpler R ==> P?
4 visualizaciones (últimos 30 días)
Mostrar comentarios más antiguos
Jim Bosley
el 4 de Sept. de 2022
Comentada: Jim Bosley
el 6 de Sept. de 2022
tldr;
Is there any benefit or disadvantage to writing the stoichiometry reactions of catalyzed by an enzyme as R + E --> P + E? Or is it better to write this R --> P? There's a graphical difference: is there a numerical one?
Details
I was recently implementing a very large (>300 species) in Simbiology. I was able to create the model using lists of compartments, parameters, species, and reactions. The graphics looked like a bowl of spaghetti. I made some progress on making sense of things but noted a bunch of dashed lines and wondered how those got into the model.
It turns out that if I have a reaction rate equation comprised of reactant, product, and enzyme (R, P, and E, respectively) with mass action rate expression (rate = kf * [R] * [E]) one way people write this is:
Stoichiometry: R + E --> P + E
As written, there's a dashed line on the model diagram between the Enzyme and the reaction. This was the case for the model I imported. In the diagram below this is case 2.
If one changes this so that we have:
Stoichiometry: R--> P
With the same rate expression, the dashed line disappears. This is shown as case 1. If you have a simple model the dashed lines might be useful. With 300 species, these dashed lines may not be what you want so much.
The issue is that adding the enzyme to both reactant and product lists then adds a bunch of zero-value differences to the rate equation for E. That is if E catalyzes a lot of reactions
dE/dt = r1 - r1 + r2 - r2 + r3 - r3 +..... + other stuff
Is there any reason that we shouldn't use the simpler R--> P stoichiometry to give a simpler diagram, and to remove useless calculations? I'm thinking that in integrating the model, there is little effect numerically of having all those (rate(i) - rate(i)) terms. Or perhaps having these terms mess up (makes less efficient) gradient calcs or sensitivity analysis?
As an aside, I would think that a mass action rate expression with E as both reactant and product might· be wrong in many cases in biology. Enzymes saturate. The case 2 stoichimetry might be thought to acknowledge this but it doesn't functionally address the issue. More properly, the reaction is probably more like case 3, below. Alternately Case 1 or Case 2, but with Michaelis-Menton kinetics rather than simple mass action. (MM is the pseudo-steady-state approximation for case 3, btw).
![](https://www.mathworks.com/matlabcentral/answers/uploaded_files/1116750/image.png)
0 comentarios
Respuesta aceptada
Arthur Goldsipe
el 6 de Sept. de 2022
I don't expect this choice to make any numerical difference. For most situations, I consider it a stylistic choice (for example, a simpler diagram versus a diagram that makes dependencies explicit). However, I can think of two situations where you would explicitly want to include a catalyst species as both a reactant and a product:
Más respuestas (0)
Ver también
Categorías
Más información sobre Scan Parameter Ranges en Help Center y File Exchange.
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!