Specter of a square signal(10Khz) at 10MHz frequency
6 visualizaciones (últimos 30 días)
Mostrar comentarios más antiguos
Iztok Grof
el 14 de En. de 2021
Comentada: Iztok Grof
el 14 de En. de 2021
I want to draw a frequency spectre of a square signal. Sampling is being performed at 10MHz, i want to see 4 polygons of that frequency
My current code is like this
close all;
%Define number of samples to take
fs = 100e3; %%% 100 kHz
f0 = 10e3; %Hz
%Define signal
t = 0:1/fs:1-1/fs;
dT = length(y);
t1=(0:dT-1)/f0/100;
dolzina=length(t);
y= zeros(1,dolzina);
y(1:fix(dolzina/2))=1;
y=[y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y];
signal = y;
figure(1)
plot(t1, signal);
%Take fourier transform
fftsignal = fft(y);
%apply fftshift to put it in the form
fftsignal = fftshift(fftsignal);
%Next, calculate the frequency axis, which is defined by the sampling rate
f = fs/2*linspace(0,30,fs);
fq = length(f)
%Since the signal is complex, we need to plot the magnitude to get it to
%look right, so we use abs (absolute value)
figure(2)
plot(f, abs(fftsignal));
i get an error, that i can't plot the transformed signal because of vectors not being the same length
can anyone help?
0 comentarios
Respuesta aceptada
Mathieu NOE
el 14 de En. de 2021
hello
there is a much faster method to generate a square signal (using square )
see demo below for signal generation and fft analysis
NB your sampling freq is 100 kHz in the code, not 10 MHz as stated in the post
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% load signal
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%% dummy data
Fs = 100e3; % sampling freq
f0 = 10e3; % signal freq
duration = 1; % signal duration (s)
samples = Fs*duration;
t = (0:samples-1)*1/Fs;
% signal = square(2*pi*f0*t); % neg / pos symetrical square wave ( -1 / +1)
signal = 0.5*(square(2*pi*f0*t)+1); % 0 / pos square wave ( 0 / +1)
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% FFT parameters
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
NFFT = 10000; %
Overlap = 0.75;
w = hanning(NFFT); % Hanning window / Use the HANN function to get a Hanning window which has the first and last zero-weighted samples.
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% display : averaged FFT spectrum
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
[freq,fft_spectrum] = myfft_peak(signal, Fs, NFFT, Overlap);
sensor_spectrum_dB = 20*log10(fft_spectrum);% convert to dB scale (ref = 1)
figure(1),plot(freq,sensor_spectrum_dB,'b');grid
title(['Averaged FFT Spectrum / Fs = ' num2str(Fs) ' Hz / Delta f = ' num2str(freq(2)-freq(1)) ' Hz ']);
xlabel('Frequency (Hz)');ylabel(' dB')
text(locs+.02,pks,num2str(freq(locs)))
function [freq_vector,fft_spectrum] = myfft_peak(signal, Fs, nfft, Overlap)
% FFT peak spectrum of signal (example sinus amplitude 1 = 0 dB after fft).
% Linear averaging
% signal - input signal,
% Fs - Sampling frequency (Hz).
% nfft - FFT window size
% Overlap - buffer overlap % (between 0 and 0.95)
signal = signal(:);
samples = length(signal);
% fill signal with zeros if its length is lower than nfft
if samples<nfft
s_tmp = zeros(nfft,1);
s_tmp((1:samples)) = signal;
signal = s_tmp;
samples = nfft;
end
% window : hanning
window = hanning(nfft);
window = window(:);
% compute fft with overlap
offset = fix((1-Overlap)*nfft);
spectnum = 1+ fix((samples-nfft)/offset); % Number of windows
% % for info is equivalent to :
% noverlap = Overlap*nfft;
% spectnum = fix((samples-noverlap)/(nfft-noverlap)); % Number of windows
% main loop
fft_spectrum = 0;
for i=1:spectnum
start = (i-1)*offset;
sw = signal((1+start):(start+nfft)).*window;
fft_spectrum = fft_spectrum + (abs(fft(sw))*4/nfft); % X=fft(x.*hanning(N))*4/N; % hanning only
end
fft_spectrum = fft_spectrum/spectnum; % to do linear averaging scaling
% one sidded fft spectrum % Select first half
if rem(nfft,2) % nfft odd
select = (1:(nfft+1)/2)';
else
select = (1:nfft/2+1)';
end
fft_spectrum = fft_spectrum(select);
freq_vector = (select - 1)*Fs/nfft;
end
4 comentarios
Mathieu NOE
el 14 de En. de 2021
hello again
regarding your comment : the signal have lower amplitude of 0 and higher amplitude of 1
is exactly what I suspected , so this is the simplest way to generate it (as in my code) :
signal = 0.5*(square(2*pi*f0*t)+1); % 0 / pos square wave ( 0 / +1)
Más respuestas (0)
Ver también
Categorías
Más información sobre Discrete Fourier and Cosine Transforms en Help Center y File Exchange.
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!