adhavan d

Last seen: 9 días hace | Con actividad desde 2023

Followers: 0 Following: 1

Programming Languages:
MATLAB
Spoken Languages:
English
Pronouns:
He/him

Estadística

Feeds

Pregunta

LUT-based IPMSM Reference Block: Flux-Weakening Id/Iq Too High vs MotorCAD (R2025a)
Issue: PMSM FOC – Flux Weakening Region Current Optimization I’m using Motor Control Blockset (R2025b) for FOC of a PMSM and fa...

alrededor de 1 mes hace | 1 respuesta | 0

1

respuesta

Pregunta

issue on Machine losses Calculation and inverter loss calculation
When we try to extract loss for machine and inverter,we failiured to get results.we are using inverter and ipmsm motor from FEM ...

3 meses hace | 1 respuesta | 0

1

respuesta

Pregunta

Output Torque is not met request torque ipmsm and FOC plus Torque control
inverter output line current peak 494.5 Amps and phase Current peak is 285 Amps. Actual id -94 Amps actual Iq is 266.3 Amps. Ld ...

5 meses hace | 0 respuestas | 0

0

respuestas

Pregunta

Why output results are coming 50 Nm when i checked pmsm block .actualy ipmsm machine model has to be generate 60 Nm for 300 phase current( id is -82 Amp, iq is 268 Amp).but i
I am using pmsm block with delta connection for three phase inverter and Torque controller with FOC . i checked inverter outp...

5 meses hace | 1 respuesta | 0

1

respuesta

Pregunta

When run the model ,the error is shown. before, I had used Ideal mosfet.no error occurred. Now i am using N channel mosfet from simscape.no errorr is. occured
I want results from community for how to rectify the issue. I am developing plant model and controller model for my project u...

5 meses hace | 0 respuestas | 0

0

respuestas

Pregunta

how to find out overcoming force in linear actuator model
how to find out overcoming force in linear actuator model? I am using linear actuator model. Power supply dc is applied to mode...

más de 1 año hace | 1 respuesta | 0

1

respuesta

Pregunta

When I change demand position value , actuator does not respond demand value.it show only maximum position length value .Maximum position is 2.5mm.
I am using FEM based linear actuator. with close loop controller.Close loop controller consists of Position,Velocity and Current...

más de 1 año hace | 0 respuestas | 0

0

respuestas

Pregunta

hi, i am using FEM based linear Actuator issue. I could not measure force and position at same time.
hi, i am using FEM based linear Actuator issue. I could not measure force and position at same time.Please give Proper solution...

más de 1 año hace | 0 respuestas | 0

0

respuestas

Pregunta

Ideal Translational Motion Sensor block(position) does not work on linear actuator model.
when I apply both Ideal Translational Motion Sensor block and Ideal Force Sensor block at same time on my linear actuator model,...

más de 1 año hace | 1 respuesta | 0

1

respuesta

Pregunta

why do all matlab actuators examples use force as input source?.in real, force is output of actuators.
why do all matlab actuators examples use force as input source?.in real, force is output of actuators. in my project,actuator's...

más de 1 año hace | 1 respuesta | 0

1

respuesta

Pregunta

how to put input value for FEM-Parameterized Linear Actuator (.1)Flux partial derivative wrt current, dPhi(i,x)/di (unit is web/A )2)Flux partial derivative wrt displacement)
how to put value for FEM-Parameterized Linear Actuator? I have matrix values of magnetic flux (web) for displacement vector wit...

más de 1 año hace | 1 respuesta | 0

1

respuesta

Pregunta

Flux are available almost many places in Linear Actuator . in Which place Flux can be used in FEM-Parameterized Linear Actuator block ?
Flux are available almost many places in Linear Actuator . in Which place's Flux can be used in FEM-Parameterized Linear Actuat...

más de 1 año hace | 0 respuestas | 0

0

respuestas

Pregunta

Flux weakening equation issue
i have modelled using subsystem block for flux weakening equation(IPMSM) which is available in mathworks website.but output of...